Plastic Pipe Extrusion Line

Plastic Pipe Extrusion Line
Plastic Pipe Extrusion Line
Beisu Plastic Pipe Extrusion Line is used to produce plastic pipe in different raw material, at present, we have PE/PP/PPR pipe production line,PVC pipe production Line,Single wall corrugated pipe production line.
Our Plastic Pipe Extrusion Line can be a single screw extruder or twin screw extruder.
The single-screw extruder conveys materials by friction, and its melting and plasticizing effect is not as good as the twin-screw extruder, but the cost is very low.
At present, polyethylene and polypropylene pellets are generally formed by single-screw extruders. Most of the screws are not conventional three-section full-thread screws, but mixing elements are added to the screw to enhance the mixing and plasticizing effect.
The raw material of polyvinyl chloride is in powder form. If it is produced by a single screw extruder, it must be mixed and granulated in advance, which increases the production process.
Therefore, the current production of PVC powder directly uses a conical twin-screw extruder for mixing and molding. When designing or selecting the extruder screw for PVC pipe extruder machine, its structure and parameters should consider the heat-sensitive performance of PVC (especially rigid PVC).
Plastic Pipe Extrusion Line Video
Plastic Pipe Extrusion Line APPLICATION
PE
PP
PPR
PVC
Single wall corrugated pipe
Brief introduction of plastic pipe production line:
The plastic pipe industry has preliminarily formed with polyvinyl chloride (PVC-U) pipe, polyethylene (PE) pipe and polypropylene (PP-R) pipe. Among them, polyethylene (PE) pipes are widely used in building water supply, building drainage, buried drainage pipes, building heating, gas transmission and distribution, gas transmission pipes, electrical and telecommunications protection sleeves, industrial pipes, etc. due to their unique advantages. Agricultural pipes, etc. It is mainly used in urban water supply, urban gas supply and farmland irrigation.
The plastic pipe production line includes A extruder, B extruder, air distribution plate, single/double wall die, cooling water jacket, molding machine, vacuum pump, C extruder, outer composite mold, vacuum setting spray box, Traction machine, cutting machine and pipe stacker; plastic pipe production line has the advantages of reasonable structure, advanced design, high degree of automation, fast production speed, simple operation, good stability and low cost. It can also produce single-wall corrugated pipes, double Four different pipe structures: wall corrugated pipe, double-layer composite corrugated pipe, and three-wall corrugated pipe, all of which have high ring stiffness, high tensile strength, low cost, and at the same time, can adapt to excavation and trenchless construction use.
Process flow of plastic pipe production line:
Vacuum feeding-----hot melt extrusion-----vacuum sizing-----secondary spraying-----printing traction-----product cutting-----visual view Detection-package and store
Operating Regulations of Plastic Pipe Production Line:
1. Turn on the power supply, turn on the host, set the process temperature of the co-extrusion machine, turn on the temperature control host, the co-extrusion machine will heat up, turn on the feeder and the dryer.
2. Install the sizing sleeve, shaped spray flange, sealing gasket, etc. for the production pipe specifications.
3. According to the production pipe specifications, install the Huff block of the cutting machine and adjust the position of the knife.
4. Install the traction tube and adjust the position of the tug.
5. Adjust the center position of the production line.
6. Connect water, electricity and gas.
7. Add water to the vacuum box and spray box to the specified position.
8. Adjust the water curtain of the sizing sleeve to make the water flow evenly.
9. The temperature of the die head reaches the set temperature, and the die and heart die are replaced.
10. Adjust the gap between the die and the mandrel, the left and right are the same, the upper part is slightly larger than the lower part.
11. Saw the traction pipe connection oblique opening
12. Open the feeding baffle after the host holding time is up, turn on the host and adjust it to about 10 revolutions.
13. After the heat preservation time of the co-extruder is up, open the feeder baffle, turn on the co-extruder, and adjust it to about 20HZ.
14. Check the discharge condition of the main machine and whether the plasticization is good. The wall thickness of the water pipe can be adjusted according to the deviation of the discharge.
15. Preheat the traction tube and turn on the vacuum setting water pump and vacuum pump at the same time, and adjust the water flow rate of the sizing sleeve.
16. Press down the crawler on the tractor, and set the traction speed according to the speed of the main engine at the same time.
17. Bond the extruded pipe and the traction pipe, and then turn on the traction machine.
18. Make a mark on the pipe, debug it, and pay attention to the wall thickness. Should be adjusted early to avoid other
19. Turn on the spray box water pump in turn according to the position of the pipe.
20. After the tube is adjusted, put down the length measuring wheel of the tractor and turn on the inkjet printer
Plastic Pipe Extrusion Line
Beisu machine have PE/PP/PPR pipe production line,PVC pipe production Line,Single wall corrugated pipe production line.

Plastic Pipe Extrusion Line FAQ

How is the plastic pipe production line formed?

The plastic pipe production line is composed of control system, extruder, head, setting cooling system, tractor, planetary cutting device and turnover frame.

Composition of PE pipe production line

Each pipe production line has two extruders. One extruder mainly adopts strong conveying bushing and high-efficiency screw, and the other smaller extruder is used to extrude the marking line.

Process flow of plastic pipe production line

Vacuum feeding-----hot melt extrusion-----vacuum sizing-----secondary spraying-----printing traction-----product cutting-----visual view Detection-package and store

What is the purpose of PVC pipe production line?

PVC pipe production line is mainly used to produce PVC pipes, which are widely used in agricultural water supply and drainage, building water supply and drainage, cable laying and other aspects, as well as plastic PVC pipes with various pipe diameters and wall thicknesses. Because of its characteristics, CPVC plastic pipe is widely used in oil field crude oil gathering and transportation, chemical temperature and corrosion resistant pipeline, hot water and warm water supply and drainage pipeline, directly buried high-pressure and ultra-high-voltage power transmission, cable protection pipe and other fields.

About Beisu

BEISU machienry is professional in plastic pipe extrusion machine, plastic profile extrusion line, plastic sheet extrusion line, and plastic recycling machine with them self R&D technology team more than 10 years. All machines can be customized by your requirements, we can supply the production line drawing and suggestion for your factory before our cooperation, and we can supply our technical support with free formula after we cooperation.
Our engineer can install the plastic extruders or plastic extrusion production line for you with the reasonable salary, and we can supply training support for your staffs if you required.
We can arrange fast shipment for you, as our staffs have more than 10 years; working experience in their professional field, and we always stock some regular main parts in our warehouse.

Why choose Beisu?

1000 m2

Covering an area of 1000 m2

10 YEARS

10 years of production experience

20,00 UNITS

with an annual output of 20,00 units

CE

Has obtained CE certification

OEM

Provide OEM services

R & D

Two excellent equipment R&D teams

Beisu main products

BEISU machinery and equipment recommendation: PVC/PE/PP pipe production line, PVC/PE wood plastic production line, PVC profile/profile production line, PVC/PP/PE/ABS sheet/sheet production line, PVC edge band production line and mill, High-speed mixer (group), crusher, sharpener, shredder, tractor, winder, cutting machine and other plastic auxiliary machinery.

  • Plastic Pelletizing Line

  • Plastic Pipe Extrusion Line

  • Plastic Profile Extrusion Line

  • Plastic Shredding Crushing Machine

Please enter your message


    Open chat